Quick Lift
A: Will not. After a sudden power failure, the equipment will automatically maintain the voltage and maintain the state at the time of the power failure, neither rising nor falling. The power unit is equipped with a manual pressure relief valve. After manual pressure relief, the equipment will slowly fall.
Pls refer to the video.
A: The stability of Quick Lift is very good. The equipment has passed the CE certification, and the partial load tests in the four directions of front, back, left, and right, all meet the CE standard.
Pls refer to the video.
A: Quick Lift is a split structure. After the vehicle is lifted, the bottom space is completely open. The minimum distance between the vehicle chassis and the ground is 472mm, and the distance after using heighten adaptors is 639mm. It is equipped with a lying board so that personnel can easily perform maintenance operations under the vehicle.
Pls refer to the video.
A:If your car is modern it will probably have jacking points. You need to know the distance
between jacking points to get the correct quick lift model.
A: Refer to the car’s manual where they should be images indicating their location. Or you can personally measure the distance between the car's lift points.
A: Measure the centre to centre distance between the jacking points and identify a suitable quick Lift using our comparison table.
A: You will need to measure the distance between the front and back tyres and check that the quick Lift will slide under the car.
A: As long as the wheelbase of the vehicle is less than 3200mm, then you have to choose the quick lift suitable for your car according to our comparison table.
A:There are extension frame L3500L that can be used with the L520E/L520E-1/L750E/L750E-1 to provide a longer jacking point range.
A: The initial height of the quick lift with L3500L extension frame is increased to 152mm, so you need to measure the vehicle's ground clearance to make sure it slides under the car.
A: If it is a medium-sized or small SUV, please choose L520E/L520E-1/L750E/L750E-1 according to the weight of the vehicle.
If it is a large SUV, please measure the distance between the lifting points of the vehicle and select the following solution according to our comparison table: 1.L520E/L520E-1+L3500L extension frame+L3500H-4 height adapter. 2.L750HL.3.L850HL.
A: We recommend：L750E + L3500L expansion frame + L3500H-4 height adapter. This combination can accommodate both short and long wheelbase models, as well as SUVs and pickups.
Inground Lift
A: Inground Lift is very easy for maintenance. The control system is in the electric control cabinet on the ground, and it can be repaired by opening the cabinet door. The underground main engine is the mechanical part, and the probability of failure is low. When the sealing ring in the oil cylinder needs to be replaced due to natural aging (usually about 5 years), you can remove the support arm, open the upper cover of the lifting column, take out the oil cylinder, and replace the sealing ring.
A: Generally, it is caused by the following reasons, please check and eliminate the faults one by one.
1.The power unit master switch is not turned on,Turn the main switch to the "open" position.
2.Power unit operating button is damaged，Check and replace button.
3.User's total power is cut off,Connect the user's total power supply.
A:Generally, it is caused by the following reasons, please check and eliminate the faults one by one.
1.Insufficient air pressure, mechanical lock does not open，Check the output pressure of the air compressor, which must be above 0.6Ma，Check the air circuit for cracks, replace the air pipe or air connector.
2.The gas valve enters the water, causing damage to the coil and the gas path cannot be connected.Replacement of air valve coil to ensure that the oil-water separator of air compressor is in normal working condition.
3.Unlock cylinder damage,Replacement unlock cylinder.
4.Electromagnetic pressure relief valve coil is damaged,Replace the electromagnetic relief valve coil .
5.Down button is damaged,Replace the down button.
6.Power unit line fault,Check and repair the line.